
 |
|
 |
 |
AE06000A-1PA -
Lift Plate w/ Hooks:
WLL: 500 Lb.

This is an example of a specialty solution to a lifting problem. The
customer needed a lift system that allowed them to lift a loaded "bucket"
out of a hot oven. The result is a safe, test proven lifter specifically
designed and built to do the job.
|


 |
 |
AE08000A-1PA
- Lift Beam with Bevel Ends: WLL: 2 Ton

This lift beam was designed to assist a water department with lifting and locating precast concrete products. The beveled edges match the inside diameter of the precast shapes as it is raised horizontally. The end users have applied a piece of rubber to both ends of the beam to "protect" the precast products. Hence the four hole pattern at each end. Using this beam has saved them time and money as they have not destroyed any pieces using this beam and they can lift and place the precast faster.
|


 |
 |
AE26000A-1PA
- Triangular Lift Frame: WLL: 2 Ton

Here's triangular lift frame for a 3 point lift that was done for a major university. This style could easily be adapted for much heavier and larger applications.
|


 |
 |
K1005CB-1PA - Lift Beam Top & Bottom Sliding Lift Eyes:
WLL: 2 Ton

Time is money and you shouldn't spend it unbolting and re-bolting safety shackles just to make an adjustment. The Lift Beam with Sliding Shackles allows you to simply slide the shackle to the desired location and lock it in place,
with very close incremental adjustments, too. This lifter is value-packed, especially when working with large shackles where just bending the cotter pin can be a chore. Another unique gem from
TANDEMLOC. |


 |
 |
AA14000A-1PA - Lift Beam with Hooks: 5 Ton, 126"

This liftbeam incorporates swivel hooks for load positioning and a large bail opening for the crane hook. This is a style that can be easily customized to meet your capacity and could be outfitted with hooks that can swivel while under load. |


 |
 |
AF12A00-00A-PA - Offset Lift Beam, Adjustable: 6 Ton,
200.75"

A customer required a specialty lifting device to lift
concrete lids from containment pits. An oversight prevented the
bridge crane from reaching a position over each lid. Tandemloc
engineering designed and built a load-tested, gear driven
adjustable counter-weighted lifting device that allowed the lids
that were of different weights and sizes to be removed quickly
and safely. |


 |
|
AE28000A-1PA - Fork Lift Beam: WLL: 10 Ton

The TANDEMLOC Fork Lift Beam increases the usability of a fork lift
by providing a single lift point between the fork blades. It attaches
easily by sliding onto blades and tightening handwheels. It includes a
Crosby Swivel Hook with latch. |


 |
|
AE28000A-2PA - Fork Lift Beam w/ Center Ring: WLL: 10 Ton

The TANDEMLOC Fork Lift Beam w/ Center Ring is the same as the
AE28000A-1PA, except that this model includes a ring in the
center of the tube which is provided as a securing point to
further secure the lifter to the forklift by simply attaching a
lanyard to the ring and tie the other end to the forklift. |


 |
 |
AE18000A-1PA - Lift Beam: WLL: 10 Ton

This liftbeam incorporates swivel hooks for load positioning and a large bail opening for the crane hook. This is a style that can be easily customized to meet your capacity and could be outfitted with hooks that can swivel while under load. |


 |
|
AD28000A-1PA - Lift Beam w/
Swivel Hooks: WLL: 15 Ton, 12' Max. Span

This liftbeam incorporates swivel hooks for load positioning and a large bail opening for the crane hook. This is a style that can be easily customized to meet your capacity and could be outfitted with hooks that can swivel while under load. |


 |
|
S35000E-TPS
- Lift Beam for Seive & Size Roll: WLL: 15 Ton

A paper company asked us to customize one of our lift beams and incorporate a chain sling bridle assembly for added stability and web slings at the bottom to handle rolls. Once again, this style can be adapted to a variety of lengths and capacities.
|


 |
 |
S35000B-1PA - Lift Beam: WLL: 5 Ton

Heres a basic lifter that incorporates a selection of lift points and crane pick points to lift a variety of cargo within the 5 ton capacity. |


 |
 |
AD12000A-1PA - Lift Beam - Adjustable 10 Ton x 12 Feet
Spread

The AD12000A-1PA has a lift eye that can be be adjusted for
off center loads. It adjusts 2 feet on either side of the middle
in 4 inch increments. The cargo hooks are also movable,
providing an overall spread of 144 inches to 150.75 inches in 6
inch increments. Of course, this versatile lift beam is a style
that can be easily tailored by Tandemloc to meet your specific
needs. |


 |
 |
AA09000A-1PA - Lift Beam: WLL: 12 Ton, 76"

This liftbeam incorporates a large loop for the crane hook with padeyes as lift points specifically located for a customers application. Another lifter easily customized to meet your needs. |


 |
|
AD11000A-1PA -
Lift Beam, Multipick: WLL: 15 Ton

Another example of a TANDEMLOC multi-purpose lift beam that
offers a multitude of lift points. Overall height is less than
26". |
|
S35000A-1PA - Lift Beam, Multi-Pick, Multi-Lift: 20 Ton, 99"

Multi pick is the word for this beam! Many top padeyes for lift points and a ton of padeyes for cargo. All sized for shackles. Length, capacity, number of
holes - have it your way! |
|
AC27000A-1PA -
Lift Beam with Sliding Padeyes: WLL: 22.5 Ton

The Lift Beam with Sliding Padeyes
saves time when preparing to lift different items. Rather
than wrestling with shackles, simply pull a pin and slide the
padeye to another location and replace the pin. This particular
item has three adjustment holes at spreads ranging from 41" to
103". As with most of our products, this style can be used to
design a lifter to meet your application. |
 |
AB17000A-1PA - Lift Beam: WLL: 23 Ton, 162"-204"

This beam incorporates a single pick padeye at the top and an array of padeyes at the bottom for multiple sling legs. Easily adaptable to meet your capacity, length or padeye requirements. |


 |
 |
AD46000A-1PA
- Lift Beam: WLL: 25 Ton, 156"

This liftbeam offers an oblong opening as a hook point with
shackle padeyes on the bottom. |


 |
 |
S36000B-1PA - Lift Beam: WLL: 40 Ton

Heres a basic lifter that incorporates a selection of lift points and crane pick points to lift a variety of cargo within the
40 ton capacity. |


 |
 |
AD16000A-1PA - Lift Beam - Lo Profile: 40 Ton for Center
Pick. Ends Rated at 65,000 LB Each Straight Pull

This is an example of a very low headroom lifter. The crane hook can lift directly from the center padeye with shackle or from each end (at 65,000 lbs each, straight pull). the clevis type ends can connect up with pendants without shackles and they are tucked up above the
bottom of the beam to reduce the headroom. The pins have safety lanyards to prevent loss.
|


 |
 |
AC29000A-1PA - Lift Beam, Multi-Pick, Multi-Lift: 50 Ton,
144"

Multi pick is the word for this beam! Many top padeyes for lift points and a ton of padeyes for cargo. All sized for shackles. Length, capacity, number of
holes - have it your way! |


 |
 |
AD29000A-1PA - Lift Beam
Mulit-Pick: WLL: 50 Ton, 25' Max. Span

Heres a lift beam with a large hook opening for your crane hook and many padeyes along the bottom, suitable for shackles. It also incorporates a stand which helps the beam stand upright when not in use. Another neat design easily adaptable for your capacity! |


 |
 |
AH38A00A-00A-PA - Liftbeam and Stand: WLL: 120 Ton

U.S. Navy called on TANDEMLOC to build a "lightweight" 240,000
lbs capacity lift beam and we answered the call with this newly
designed lifter made of T-1 alloy steel, which offers high
strength at a lighter weight than low carbon steel. The lifter
was proof tested in house to 300,000 lbs., not once but several
times, so that each padeye was loaded. |


 |
 |
AJ07A00A-00A-PA - Liftbeam: WLL: 150 Ton

This stout lift beam with a 300,000 lb working capacity was
tested to 500,000 lbs as a requirement by one of our
customers. With Tandemloc's versatile (pat pending) test
machine, this load was easily achieved. Other
manufacturers would have to jump through hoops to handle this
level of testing load. For us, it's just another day at the
office. |


 |
|
AF11A00-00A-PA -
Spreader, 2 Crane Bottom
Lift: 40 Ton, 471.88" (~ 39')

At almost 40 foot long with a work load limit
of 80,000 lbs, this beam is a departure from our other examples
of two-crane lifters. The AF11A00-00A has two lifting points
offset, making it a two crane lift beam for unequal crane
capacities. It also incorporates transverse beams for a 4 point
lift. As with almost everything we design and manufacture, this
design can be modified to suit your two crane lift needs. |


 |
|
AD51000A-1PA - Yard Crane Lift Bar: 20 Ton, 168"-250.25"

Lift from a center padeye or use a 2-leg sling (not included)
and lift from each end. Several pick points along the bottom
for versatility. |


 |
 |
AB22000A-1PA - Four Point Adjustable Spreader w/ Straps:
0.5 Tons
(Similar product shown)

This style is a telescoping lifter that offers tremendous adjustment with several pick points for your crane. Like almost all of our products, it too can be customized for capacity and size. |


 |
 |
AF0100A-1PA - "H" Lift Beam:
0.8 Tons

Although most of the lifters shown on our web site are for
heavy lifts, we can make small lifters! Here's an example of a 4
point lift beam, often referred to as an "H" Lifter, with a
working load limit of 1,600 lbs. Just like the big boys, it is
built to the same standards and we apply the same concern for
quality. It is proof tested as well |


 |
 |
AA60000A-1PA - "H" Style Adjustable Lift Beam: 3 Ton,
54"-84" x 30"-48"
(Similar product shown)

This style is a telescoping lifter that offers tremendous adjustment with several pick points for your crane. Like almost all of our products, it too can be customized for capacity and size. |


 |
 |
AE09000A-1PA - Four Point Adjustable Lift Beam: 3.25 Ton

This lift beam has a multi pick padeye along the top of the
lifter giving tremendous adjustment for off center
lifts. The ends of the lifter are designed for multiple
pendants. This lifter was specially designed for a
particular application, but could be altered to suit your
requirements. TANDEMLOC offers a tremendous library of
products and most of them can be customized.
|


 |
 |
AA33000A-1PA - "H" Style Lift Beam: 5 Ton, 60" x 40"
(Similar product shown)

This particular style offers a few pick points for off center loads and 4 single padeyes spaced 60 x 40 apart and includes chain slings. Like almost all of our products, it too can be customized for capacity and size. |


 |
 |
AC16000A-1PA - "H" Style Lift Beam: 6 Ton, 48" x 22"

This lifter incorporates a single pick padeye for lifting and 4 single padeyes for cargo. It can be customized for capacity and size |


TOP |
 |
AE15000A-1PA -
"H" Lift Frame: 6 Ton, 96" x 72"

Here is an example of one of our economical 4 point lift
beams, which can be altered to meet different load
requirements and dimensions. It has a multi pick padeye
which allows for off center lifts in one direction. Each
corner has a single padeye for sling pendants. |


 |
 |
AF0900A-1PA - Four Point Adjustable Spreader: 12.5 Ton
WLL

This 4 point lifter was designed and manufactured to lift a
critical piece of machinery. This design can be altered to
meet other dimensional and capacity requirements. |


 |
 |
S41000A-1PA - "H" Style Adjustable Lift Beam: 16 Ton,
108"-144" x 30"-48"

This style is a telescoping lifter that offers tremendous adjustment with several pick points for your crane. Like almost all of our products, it too can be customized for capacity and size. |


 |
 |
S41000C-1PA - "H" Style Adjustable Lift Beam: 16 Ton,
108"-156" x 30"-48"

This style is a telescoping lifter that offers tremendous adjustment with several pick points for your crane. Like almost all of our products, it too can be customized for capacity and size. |


 |
 |
S41000E-1PA - "H"
Style, Sliding Padeye Adjustment: 20 Ton, 84"-132" x 41"-60"

If speed of adjustment is important to you, this is the lifter design to go with. Not only does it telescope, the lift points and pick points incorporate our sliding shackle design. Simply slide the shackles to the desired location and lock in place. Takes only seconds to do and offers micro like adjustment intervals. It too can be customized for capacity and size. |


 |
 |
S41000F-1PA - Adjustable Liftbeam: 20 Ton, 90"-132"

Time is money! If speed of adjustment is important to you,
this is the lifter design to go with. Not only does it
telescope, the lift points and pick points incorporate our
sliding shackle design. Simply slide the shackles to the desired
location and lock in place. Takes only seconds to do and offers
micro like adjustment intervals of 3/4". Much faster than
disconnecting and reconnecting shackles. This product can be
customized for capacity and size. |


 |
 |
S41000F-1PA - "H" Style Lift Beam: 23 Ton, 95.10"-270.10"

One of the advantage of this design is that it accomplishes a
4 point lift just as a fixed frame four point lifter but can be
taken apart and each component can be used as a lift beam. This
product combines two adjustment methods. The main beam
incorporates multi-hole pad-eyes while the smaller end beams use
the multi hole pad eyes at the bottom and the fast acting
sliding shackle adjustment design at the top. This lifter can be
customized to meet other capacities and dimensions. |


 |
 |
S41000B-1PA - "H" Style Adjustable Lift Beam: 47.5 Ton,
96"-156" x 30"-48"

This style is a telescoping lifter that offers tremendous adjustment with a unique pick point keeping headroom as low as possible. Like almost all of our products, it too can be customized for capacity and size. |


 |
|
|