Register / Login - Contact Info 

VERTICAL CLAMP CONNECTOR (VI-SO) (K08A00A-1GA) 

The VISO Connector has a bolt-on base or it may be welded to a suitable platform. The VISO fits ISO 1161 Corner Fitting large aperture and incorporates a clamping action that removes any slack between the corner fitting and the body of the connector. Use whenever a slack free connection is preferred. Hot Dipped galvanized for rugged use


  • The grip and force exerted by the clamp arm (Piece 20) is variable by rotating the drive stud (Piece 30.) Max load on the hex drive is 50 ft/lb.
• STRENGTH RATINGS:
Maximum allowable loads for one VI-SO
44,000 Lbs. - Restraint against upward force
50,000 Lbs. - Traverse shear
200,000 Lbs. - Compression
HIGHER STRENGTHS AVAILABLE
  • Two grease fittings allow for easy lubrication.
  • Dimensions without tolerance are subject to manufacturing tolerances.
• Use for a slack-free, clamp-down connection of ISO 668 type container or similar structure. Connector enters the large bottom aperture of the standard corner fitting (ISO 1161) & clamps down on the inside of the bottom wall.

While this standard VI-SO is not designed for single wheels or lifting, products for these purposes are available.

Use to tightly secure containers to structures such as special pallets, ships' deck, overhead beams, foundations, chassis or other containers.

While this standard VI-SO is not designed for single wheels or lifting, products for these purposes are available.
•
Order Numbers:
K08A00A-1GA: VISO Connector
K08A00A-2GA: With Rubber Pads, Weight: 15.6 LBS
K08A00A-3GA: With Mounting Hardware, Weight: 17 LBS 
K08A00A-4GA: With Rubber Pads and Mounting Hardware, Weight: 17.1 LBS
Product Photo
Download / view printer friendly data sheet(s)
Login / register to activate:
TANDEMLOC_K08A00A-1GA.pdf
Type: PDF File
Size: 139 KB
Tandemloc's Credit Application Form
(Note: Credit Applications will only be processed with an accompanying purchase order.)


Available with rubber pads for cushioning. Mounting hardware available, too!

VI-SO grips the corner tightly, in contrast to other commonly used twist locking connectors which have approximately 1/4" of "play".

Use also to connect other items to a container such as antenna, air conditioners, davits or railings.
A. Use - for a slack-free, clamp-down connection of each corner of an ISO 668 type container such as a deck or other structure, lower the container so that the open connector enters the large bottom aperture of each ISO 1161 standard corner fitting. The clamp arm bears down on the inside of the bottom wall when the drive stud is screwed in. C. The VI-SO is to be bolted to the desired structure using four 3/4" SAE Grade 8 steel cap screws. Special flat head cap screws and locknuts are available with hex sockets on both ends. This permits the cap screw to be held from the threaded end while turning the lock nut (useful when the head end is not accessible).
B. Use cap screws and lock nuts to assemble the connector to a suitable receiving structure. Locate connectors per "male fitting instructions" on Tandemloc Data Sheet DF-72047-16 (Sheet 2) for standard sized structures. For non-standard sizes use the principles implied on this sheet to determine your location. D. To secure an ISO container or similar structure first open the connector fully by turning the drive stud counterclockwise until it is within (Sheet 1) dimension. Lower container so that the upward projecting portions of the connector enter the large apertures in the bases of the corner fittings. Turn the drive stud clockwise to secure.



AT LEAST TWO OPPOSING VERTICAL CLAMPS ARE REQUIRED TO SECURE

Call Toll-Free: 1-800-258-7324 • Toll-Free Fax: 1-800-892-3273 • info@tandemloc.com • Site Map • Contact Us
TANDEMLOC, Inc · 824 Highway 101 · Havelock, NC 28532 USA · Legal Information

© 2008 Tandemloc, Inc. All rights reserved. All content displayed on this site is either the property of, or used with permission by, Tandemloc, Inc. republication or redistribution of the content, including by framing or similar means, is prohibited without the prior written consent of Tandemloc, Inc. The use of any of the content contained herein by you, or anyone else authorized by you, is prohibited. Any unauthorized use of the content may violate copyright laws, trademark laws, the laws of privacy and publicity and statutes of the U.S. and/or other countries. TANDEMLOC™, TANDEMLOC® logo, and TANDEMLOC AUTOLOC™ are the trademarks or registered trademarks of Tandemloc, Inc. Any unauthorized use of these or other Tandemloc, Inc. trademarks is prohibited.

Products include lifting, mobilizing and securing products for below the hook and ISO container handling. Tandemloc provides standard corner fittings, lift beams, spreader bars, pipe end caps, container lifting devices, lifting attachments, twistlocks, d-rings, heavy duty casters, container casters, container lifting dollies and more.

Designed and deployed by Industrial Advertising · Links Page